In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Are cribbed ends okay for wood stacks?

Discussion in 'The Wood Pile' started by Backwoods Savage, Jun 5, 2017.

Page 3 of 3
  1. FatBoy85

    FatBoy85

    Joined:
    Feb 25, 2017
    Messages:
    6,611
    Likes Received:
    25,251
    Location:
    Washington State
    Yeah bud I cant seem to get a stack worth chit getting started and then they tip. They look ok but wobble like a leaning tower. I need to test this out. Now i could go to cheating like stacking square wood then working my way around splits and shims. Trust me this is new territory.
     
    FatBoy85, Jun 8, 2017
    #41 Top
    Shawn Curry and Barcroftb like this.
  2. FatBoy85

    FatBoy85

    Joined:
    Feb 25, 2017
    Messages:
    6,611
    Likes Received:
    25,251
    Location:
    Washington State
    Tell you what Dennis, I'll take a picture of some apple wood I stacked like last month. I cribbed the ends. They just have been made for the stack height. Thats it . But i like the critique so its ok. Funny how i have lots of small rounds split in half. But those rounds have a lot of small branch bumps and that seems to contribute a lot to the teetering i get sometimes.
     
    FatBoy85, Jun 8, 2017
    #42 Top
    Shawn Curry and Backwoods Savage like this.
  3. Backwoods Savage

    Backwoods Savage Moderator

    Joined:
    Oct 4, 2013
    Messages:
    46,966
    Likes Received:
    295,837
    Location:
    Central MI
    Oh yes. I try to keep any knots off the cribbed ends but do sometimes use them if not too bad but do not want any other piece touching there.
     
    Backwoods Savage, Jun 8, 2017
    #43 Top
    FatBoy85, Shawn Curry and Barcroftb like this.
  4. FatBoy85

    FatBoy85

    Joined:
    Feb 25, 2017
    Messages:
    6,611
    Likes Received:
    25,251
    Location:
    Washington State
    IMG_1969.JPG IMG_1972.JPG

    Backwoods Savage, so I cribbed these then worked my way up along the stack. Again you notice the t stakes but it was really for error. They are quite stable and I may be able to just take them out. The good thing is that the stack in the middle squeezes out so these ends feel solid.
     
    FatBoy85, Jun 9, 2017
    #44 Top
  5. Backwoods Savage

    Backwoods Savage Moderator

    Joined:
    Oct 4, 2013
    Messages:
    46,966
    Likes Received:
    295,837
    Location:
    Central MI
    Not bad but you can keep in mind a few changes for your next ends which will make the ends much stronger.

    Looking at the stack on the left, the most glaring error is toward the top. Look how that one split is on the left; it is not solid at all as it should have been turned so that a flat side was down. Look at the 4th tier up from the bottom. That outside piece is not totally on the piece below it. Little things like this make it a bit unstable or at least not as strong as it should be.

    Not to pick out the whole thing but just little things. Look at the picture on the right. Bottom piece on the end. Should have been turned around so that flat side pointed out. It would not mean much but if you make a habit out of looking for that sort of thing when building it will go better for you. Only one other comment then I'll stop. In that same picture, 5th level. You have one split on top of the other in order to "level" it out. That is a definite no-no. Very weak especially if it is low in the stack as weight on top will cause that to collapse in time.

    I could point out a few other minor spots but this is enough. Good luck.
     
    Backwoods Savage, Jun 9, 2017
    #45 Top
    BigPapi and FatBoy85 like this.
  6. FatBoy85

    FatBoy85

    Joined:
    Feb 25, 2017
    Messages:
    6,611
    Likes Received:
    25,251
    Location:
    Washington State
    Thanks I'll keep an eye out for this sorta thing and try again.
     
    FatBoy85, Jun 9, 2017
    #46 Top
    Backwoods Savage likes this.
  7. Backwoods Savage

    Backwoods Savage Moderator

    Joined:
    Oct 4, 2013
    Messages:
    46,966
    Likes Received:
    295,837
    Location:
    Central MI
    I hope I was not out of line there.
     
    Backwoods Savage, Jun 9, 2017
    #47 Top
    FatBoy85 likes this.
  8. FatBoy85

    FatBoy85

    Joined:
    Feb 25, 2017
    Messages:
    6,611
    Likes Received:
    25,251
    Location:
    Washington State
    Absolutely not I had to run out for work and reply quick but for what its worth I have never really got the cribbing down because I wasnt taught how to put uneven splits in that kind of stacking. Honestly if its a tutorial that id have fun with at a GTG, Im game! :thumbs:
     
    FatBoy85, Jun 9, 2017
    #48 Top
    Backwoods Savage likes this.
Page 3 of 3