In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Cookie Time II...

Discussion in 'Chainsaws and Power Equipment' started by Chvymn99, Aug 9, 2014.

Page 2 of 2
  1. HDRock

    HDRock

    Joined:
    Oct 4, 2013
    Messages:
    17,261
    Likes Received:
    60,482
    Location:
    Grand Blanc, MI,
    blooper vid :rofl: :lol: no harm done
     
    HDRock, Aug 9, 2014
    #21 Top
    Chvymn99 likes this.
  2. DexterDay

    DexterDay Administrator

    Joined:
    Oct 2, 2013
    Messages:
    12,411
    Likes Received:
    31,632
    Location:
    Northeast Oh
    Awesome video!! Awesome saws!! Some of those sucker were flying!!
     
    DexterDay, Aug 9, 2014
    #22 Top
    Kg461 and Chvymn99 like this.
  3. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    There was stock to ported run.
     
    Cut4fun, Aug 9, 2014
    #23 Top
  4. DexterDay

    DexterDay Administrator

    Joined:
    Oct 2, 2013
    Messages:
    12,411
    Likes Received:
    31,632
    Location:
    Northeast Oh
    Yes.. Ported and Stock.....

    . But the 665 was Stock!! :dex:

    That is amazing!! As long as all chain was on a level playing field. There was knots, and a part was slightly larger in diameter. But... For the most part was pretty equal. Ported or not? The most impressive to me was the 665.

    And I seen the comment about the stopwatch in the 372 thread ;) I had it out for these times :) That was the next thread I seen and figured I do the same thing. :thumbs:
     
    DexterDay, Aug 9, 2014
    #24 Top
    mdavlee and Chvymn99 like this.
  5. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    I'm cornfused with post :confused:. I was talking about MY video I posted being stock to ported saws. :cool:

    I kept stopwatch in the desk, 1 over the bench and 1 in box for saws.
     
    Cut4fun, Aug 9, 2014
    #25 Top
    DexterDay likes this.
  6. Chvymn99

    Chvymn99 Moderator

    Joined:
    Oct 4, 2013
    Messages:
    21,172
    Likes Received:
    111,987
    Location:
    KC Metro
    Dex,

    The 46 & 660 ran the same setup. I started with a new chain. The 562xp & 665 ran the same chain & bar combo with 7 previous cuts on it. The 562xp ran first and then the 665. While the 46 ran 7 pin, 8 pin followed by 660 8 pin then 7 pin.
     
    Chvymn99, Aug 9, 2014
    #26 Top
    Cut4fun likes this.
  7. DexterDay

    DexterDay Administrator

    Joined:
    Oct 2, 2013
    Messages:
    12,411
    Likes Received:
    31,632
    Location:
    Northeast Oh

    Oh.. My bad..:(

    Based on the times? I knew some of those were not ported or race saws. But some of them clearly were (when they cut like a hot knife through butter ;)
     
    DexterDay, Aug 9, 2014
    #27 Top
    Cut4fun likes this.
  8. DexterDay

    DexterDay Administrator

    Joined:
    Oct 2, 2013
    Messages:
    12,411
    Likes Received:
    31,632
    Location:
    Northeast Oh

    That's equal enough. The 562 ran good and seemed to run a higher RPM in the cut. But the grunt of the 665 is just short of Magnificent! !
     
    DexterDay, Aug 9, 2014
    #28 Top
    mdavlee and Chvymn99 like this.
  9. mdavlee

    mdavlee

    Joined:
    Oct 21, 2013
    Messages:
    4,380
    Likes Received:
    10,479
    Those solo are impressive. I've run a stock 681 that was pretty strong.
     
    mdavlee, Aug 9, 2014
    #29 Top
    DexterDay, Cut4fun and Chvymn99 like this.
  10. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    I've ran solo 681's and thinking 651 which was online to the 5100S. Back in 2008.

    One of my GTG's I used to have.

    [​IMG]
     
    Cut4fun, Aug 9, 2014
    #30 Top
    HoneyFuzz, DexterDay and mdavlee like this.
  11. mdavlee

    mdavlee

    Joined:
    Oct 21, 2013
    Messages:
    4,380
    Likes Received:
    10,479
    Paula 681

     
    mdavlee, Aug 9, 2014
    #31 Top
    HoneyFuzz, DexterDay, Chvymn99 and 1 other person like this.
  12. HoneyFuzz

    HoneyFuzz

    Joined:
    Jan 20, 2014
    Messages:
    4,491
    Likes Received:
    14,868
    Location:
    Northeast , Ohio
    You are blessed with some of the nicest...coolest saws available buddy !! And you are enjoying them....and with the vids..we are enjoying them too !! I still think that 562xp stinks..and should be sent to me to "sit" on my shelf :)
     
    HoneyFuzz, Aug 10, 2014
    #32 Top
    Chvymn99 and concretegrazer like this.
  13. Chvymn99

    Chvymn99 Moderator

    Joined:
    Oct 4, 2013
    Messages:
    21,172
    Likes Received:
    111,987
    Location:
    KC Metro
    Thanks, Bud! Now, I just need to get them all cleaned up like yours again.... So they'll be ready to go... But the more I run that 562 the tighter my grip I get on that thing. It's just smooth. I can wait to see how it comes to the ported 362/034/036 saws....:popcorn:When they get back...
     
    Chvymn99, Aug 10, 2014
    #33 Top
    MasterMech, concretegrazer, HoneyFuzz and 1 other person like this.
Page 2 of 2