Pellet heads!! What's up today?

Going to do our Christmas today , our girls have to head back to NC tomorrow Amy has to be back to work on Tuesday , it was a short visit , but it's better than no visit . Just hope the white chit is over when they leave , 3-5 is the call for here .

 

This stuff only happens to me on holiday weekends!!

At least they are open on Wednesday, years past they were closed the whole week.

Left a msg on dentists cell phone to give me a quick call. I dont want to mess up the implant-pretty sure I cant as that is set in bone, but JIC. Told him on msg I know it can wait till Wednesday but would appreciate a call back. Didnt wish him a Merry Christmas as my mind was elsewhere I'll take care of that if he actually calls back.

 

Not a bad idea, wish we were doing that. Tomorrow is forecasting 6-8" of blowing chit and I am suppose to drive to my sisters in Mass. Likely not heading down there as the worst of it is going to be in the morning till early afternoon.

Gonna be in Kittery tonight, Christmas with my honey and her kids in the morning then play it by ear.

 

Never fails, always during a holiday or something!

 

Gotta follow Dr. Will's advice and liquid diet(smoothies) until the appointment for the dentist
Not a funny time to poke you and poor timing on your part
Hoping for realistic outcome

 

I have never had a dental issue that wasnt on a holiday weekend.

Tempting for sure

Why not? I would-gotta laugh

The crown is intact but has a small chip at the base. I dont know if that would make it not reusable and just need to be glued back on the abutment?

Not too worried about it. Cant change what has already happened. I guess just have to be careful till Wednesday.

No call from the Dr yet. I am not asking for anything more than a few questions answered. He must be busy

 

Gorilla glue

 

Predicting 2-6" here overnight tonight, so younger daughter will be leaving a little later than originally planned.

 

Probably would work

Dr called and he offered to go in to the office today-told him it wasnt necessary if I was OK without the crown on the post and I was more concerned with possible damage to the post on the implant. He says its titanium and I would have to chew on a rock to damage it. Not making him go in and will see him wednesday. He also said if the crown cant be reused it would be replaced by the manufacture as it shouldn't have broken.

 

Now its time to get out of here and head to Kittery.

Merry Christmas All !!!!

 

Merry Christmas

 

Merry Christmas Everyone.

 

As we say in this house, merry catmas.

 

Well, the resident squirrel isn't too happy - must have been using one or both of the Sportages for winter storage that got towed out on Thursday..

This is basically what I was presented with today while loading trash to take down to the town dump:



Guess it's time to put the feeder back up again.

Loading up the tools to take the '01 Intrigue down to work, the owner & lead mechanic said I could use the Service Bay to make the repair, very cool of them. Being out of the weather is a real gift, after last evening.

Have a fun evening all: watch out for that Crazy guy wearing a Red suit!

 

since today was so nice, with a little sun in the afternoon, I did the LaCrete / MWP softi swap. took the MWP to Davids, (son) and returned the trailer to the shop.

We were up at midnight, 3AM and 4:30 with a screaming 16 month old. so, a 4:30 start to today... one of his last teeth is giving him problems, i suspect. He still was a joy.

Off to my old neighbors house for a couple hours or so. its a good time except for my EX sometimes is there...... even after 20 years divorced, i do not deal with her well...

Merry Christmas to all!! stay safe tonight and drive careful tomorrow.

 

Merry Christmas everyone!

 

Merry Christmas to all !! Be safe and enjoy the festivities. Sons wife and little one got a stomach bug, hoping they will make it here tomorrow.

Doggy

 

Merry Xmas everyone! Just heading to the casino to celebrate my son's 21st birthday at midnight!

 

When I was installing the chute to my SnowTek (Ariens) It took me a while to figure out what those two bolts were for. I also bought a bag of a extra's when I bought the machine last spring.