In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

NC 30 install

Discussion in 'Modern EPA Stoves and Fireplaces' started by capetownkg, Sep 25, 2015.

Page 2 of 4
  1. papadave

    papadave

    Joined:
    Oct 3, 2013
    Messages:
    18,181
    Likes Received:
    82,470
    Location:
    Right where I want to be.
    Oh. :headbang:
     
    papadave, Oct 2, 2015
    #21 Top
    wildwest and HDRock like this.
  2. capetownkg

    capetownkg

    Joined:
    Oct 4, 2013
    Messages:
    797
    Likes Received:
    3,147
    Location:
    southern, MD
    It doesnt say in the manual about any clearances above...
     
    capetownkg, Oct 2, 2015
    #22 Top
    wildwest likes this.
  3. papadave

    papadave

    Joined:
    Oct 3, 2013
    Messages:
    18,181
    Likes Received:
    82,470
    Location:
    Right where I want to be.
    papadave, Oct 2, 2015
    #23 Top
    wildwest, Scotty Overkill and HDRock like this.
  4. mattjm1017

    mattjm1017

    Joined:
    Oct 3, 2013
    Messages:
    1,825
    Likes Received:
    3,259
    Location:
    North Eastern North Cackalacky
    Maybe mike holton can help you with your overhead clearances question I do believe he is associated with Englander.
     
    mattjm1017, Oct 2, 2015
    #24 Top
    wildwest, Scotty Overkill and papadave like this.
  5. mattjm1017

    mattjm1017

    Joined:
    Oct 3, 2013
    Messages:
    1,825
    Likes Received:
    3,259
    Location:
    North Eastern North Cackalacky
    mattjm1017, Oct 2, 2015
    #25 Top
    wildwest, HDRock and papadave like this.
  6. HammerheadC4

    HammerheadC4

    Joined:
    Dec 9, 2014
    Messages:
    153
    Likes Received:
    674
    Location:
    Eastford CT
    That looks NICE Capetown
     
    HammerheadC4, Oct 3, 2015
    #26 Top
    Scotty Overkill and wildwest like this.
  7. Chvymn99

    Chvymn99 Moderator

    Joined:
    Oct 4, 2013
    Messages:
    20,798
    Likes Received:
    109,232
    Location:
    KC Metro
    X2 :yes:
     
    Chvymn99, Oct 3, 2015
    #27 Top
    Scotty Overkill likes this.
  8. capetownkg

    capetownkg

    Joined:
    Oct 4, 2013
    Messages:
    797
    Likes Received:
    3,147
    Location:
    southern, MD
    Well went for the liner install today... didnt quite work out. I ran the liner down and had my wife let me know when it was at the stove. She just isnt strong enough to bend the pipe the tiny little bit it needs to as I pull up on it from the roof. So has to wait to get finished till I get some other help tomorrow.
    20151005_174349.jpg
    Just that little bit off :(
    20151005_182252.jpg
     
    capetownkg, Oct 5, 2015
    #28 Top
    Scotty Overkill, HDRock, Chvymn99 and 3 others like this.
  9. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,134
    Likes Received:
    141,291
    Location:
    Wyoming high plains
    We had the same exact problem :headbang:

    Ended up scooting the insert back to meet the liner, we were beat and waited just long enough into fall that we needed the heat that very evening. The insert is still there today, a few inches inside where the faceplate should go. :picard: Atleast it is there if we need it.....
     
    wildwest, Oct 5, 2015
    #29 Top
  10. fishingpol

    fishingpol

    Joined:
    Oct 3, 2013
    Messages:
    6,502
    Likes Received:
    39,643
    Location:
    Merrimack Valley, Ma.
    Oh, that is frustrating. Do you have room to push the stove back a little?
     
    fishingpol, Oct 5, 2015
    #30 Top
    Scotty Overkill, wildwest and papadave like this.
  11. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,134
    Likes Received:
    141,291
    Location:
    Wyoming high plains
    Cannot say for sure whether it was wood burner or pellet burner, I read a member here has a quick-disconnect so he can scoot his stove out and clean it, wonder if there are any adapters like that for your situation?
     
    Last edited: Oct 5, 2015
    wildwest, Oct 5, 2015
    #31 Top
  12. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    23,415
    Likes Received:
    150,342
    Location:
    NE Ohio
    I had the same issue. If I had not had my pantys in such a wad to see the durn thing blowin smoke, I would have just ordered a SS 15* elbow made for just such a problem. What I did do was to slide a small automotive style hydraulic jack under the center of the stove with a piece of 3/4" plywood in between, unbolted the legs, carefully lowered it down and then pulled it out a bit too.
    This allowed a better angle and more leverage on the liner (mine was pre-insulated so it was a bit stiffer than a normal liner) and then once attached I slowly slide the stove back in and up at the same time. Since this put a bit of pressure on the liner in the area of the old fireplace damper, and I didn't want to tear things up, I slide some sheet metal (actually, some pieces cut out of old duct work) over the sharpish front and rear edge of the damper so the liner would have something smooth to slide over. I t worked out well. The tight clearances of the whole setup did make for a lil fun fabricating/fitting/installing the block off plate then too...:picard:
     
    brenndatomu, Oct 5, 2015
    #32 Top
    Scotty Overkill, capetownkg and wildwest like this.
  13. Norky

    Norky

    Joined:
    Oct 20, 2013
    Messages:
    972
    Likes Received:
    3,083
    I had to modify my blower to get the stove far enough into the opening to connect the flue.
     
    Norky, Oct 5, 2015
    #33 Top
    wildwest and Scotty Overkill like this.
  14. capetownkg

    capetownkg

    Joined:
    Oct 4, 2013
    Messages:
    797
    Likes Received:
    3,147
    Location:
    southern, MD
    Yeah i have the blower attached otherwise I could probably get it.
     
    capetownkg, Oct 5, 2015
    #34 Top
    wildwest, Scotty Overkill and papadave like this.
  15. papadave

    papadave

    Joined:
    Oct 3, 2013
    Messages:
    18,181
    Likes Received:
    82,470
    Location:
    Right where I want to be.
    Get the other blower.
     
    papadave, Oct 5, 2015
    #35 Top
    wildwest and Scotty Overkill like this.
  16. capetownkg

    capetownkg

    Joined:
    Oct 4, 2013
    Messages:
    797
    Likes Received:
    3,147
    Location:
    southern, MD

    Yeah $62 bucks for an elbow seems a bit steep. Trying to figure a way out so I dont have to spend that and wait for it to get here.
     
    capetownkg, Oct 6, 2015
    #36 Top
    wildwest likes this.
  17. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    23,415
    Likes Received:
    150,342
    Location:
    NE Ohio
    Hmm, that does seem steep, I don't remember now the price of the ones I looked up when I did mine a couple years ago. Maybe that was another part of the reason I didn't want to use an elbow if I didn't have to.
    Just recently, I have found a little amish metal shop nearby that has SS stove pipe and fittings for about a 1/3 of what everybody else gets for the same stuff. I think maybe they make it on site...if they had a phone I'd give ya a number
     
    brenndatomu, Oct 6, 2015
    #37 Top
    wildwest likes this.
  18. Norky

    Norky

    Joined:
    Oct 20, 2013
    Messages:
    972
    Likes Received:
    3,083
    You might be able to jack the front of the stove up, high enough to get the angle to attach the adapter and let the stove bend the liner as you let it back down. Can't tell the thickness of your adapter, but doing it this way could also mess up the adapter if it's not real thick.
     
    Norky, Oct 6, 2015
    #38 Top
    capetownkg and wildwest like this.
  19. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,134
    Likes Received:
    141,291
    Location:
    Wyoming high plains
    :popcorn:
     
    wildwest, Oct 6, 2015
    #39 Top
    HDRock and papadave like this.
  20. capetownkg

    capetownkg

    Joined:
    Oct 4, 2013
    Messages:
    797
    Likes Received:
    3,147
    Location:
    southern, MD
    Am i suppose to run screws thru the holes in the stove collar???
     
    capetownkg, Oct 6, 2015
    #40 Top
    papadave and wildwest like this.
Page 2 of 4