In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Surge protector green LED protection light off?

Discussion in 'Pellet Stoves, Pellet Fireplaces, Pellet Furnaces' started by don2222, Nov 14, 2026 at 9:22 PM.

  1. don2222

    don2222

    Joined:
    Nov 10, 2013
    Messages:
    3,448
    Likes Received:
    4,897
    Location:
    Salem NH
    Hello
    This TrippLite Isobar Isoblok428 premium surge suppressor with diagnostic LEDs was installed in 2021 on a Whitfield Optima 3 and worked well for approx 5 years. Not only does it have a green LED light to show it has power and the protection circuit light shows it is working but had a fault light that lights up red if the AC outlet phase is reversed or if there is no ground. When either one of these AC outlet wiring errors occur, the fault LED lights up red and the pellet stove control panel can still be damaged!
    In this case, when the stove had its annual fall maintenance the protection light was out. This town has had many issues in the past with power outages but not much in the past few years. However power fluctuations could still be there and not noticed. Power fluctuations can still damage very sensotive pellet stove control panels over time which certainly could have happened in this case! After the stove servicing and cleaning it fired up properly.
    Here is the delails of what happened inside this surge protector. Does it look like the control panel was saved in this case?
    When the protection light on a surge protector (such as an Isobar or similar strip) goes out, it means the internal surge-suppression components—specifically the Metal Oxide Varistors (MOVs)—have worn out or sacrificed themselves after absorbing a power surge or voltage spike. [1, 2]

    What This Means
    • Surge protection is gone: The device may still pass electricity and work like a basic multi-outlet extension cord, but it no longer protects your plugged-in electronics (like computers, TVs, or audio gear) from future surges.
    • It cannot be reset: There is no manual reset button or fix to restore the internal MOVs once they have failed. [1, 2, 3]
    Pic 1 - Highly recommended Isobar Surge protector new in box
    Pic 2 - cost of Isoblok428
    Pic 3 - protection MOV failed (green LED light off)
    Pic 4 - New Isoblok428 and surge protection restored
    Pic 5 - Control Panel worth approx $600 saved and working.
    Pic 6 - Lennox Whitfield Optima 3 with modern Satin Black high temperature satin black stove bright spray paint with VHT very high temperature flat aluminum spray paint over gold bars, fired up and is working.
    Pic 7. - Isoblok diagnostic LED instruction’s information.
    Pic 8 - Fault light on
    Pic 9 - electrical tester available at Home Depot, shows type of fault
    Pic 10 - shows black hot wire and white neutral wire in AC outlet on the wall is revered. This can damage a pellet stove control over time.
     

    Attached Files:

    Last edited: Nov 14, 2026 at 11:39 PM
    BHags and MikeInMa like this.
  2. don2222

    don2222

    Joined:
    Nov 10, 2013
    Messages:
    3,448
    Likes Received:
    4,897
    Location:
    Salem NH
    In summary:
    You can put more than one device on it. They are direct plug ins they conform to the electrical codes unlike the ones that lay on the floor that can short out from water spills or floods.. Electronic semiconductors such as Triacs, MOVs and low voltage capacitors are most likely to fail from power fluctuations

    Also it is a good practice to unplug your pellet stove during the summer or when not in use.
    Zoro tools sells them here
    https://www.zoro.com/eaton-tripp-li...410-joules-diagnostic-ultrablok/i/G316450619/

    Note:
    A Metal Oxide Varistor (MOV) is a voltage-dependent resistor that acts as a surge protection device. 1 It’s designed to protect electrical and electronic circuits from damage caused by voltage spikes and transients.
    Here is why having a surge protection LED light on a surge protector is so important. :)
    If the mov in a surge protector fails from a power surge will the next pwer surge wipe out the appliance?
    If a metal-oxide varistor (MOV) in a surge protector fails completely or is already spent from absorbing a major surge, it loses its ability to clamp future voltage spikes, meaning the next power surge can pass straight through to your appliance and potentially damage or destroy it. [1, 2, 3]
    However, what happens next depends on how the surge protector failed and how it is built:
    • No More Protection (Zombie Power Strip): Many basic surge protectors keep letting electricity flow to your plugged-in devices even after the MOV has sacrificed itself or degraded into uselessness, leaving your gear unprotected. [1, 2]
    • Open Circuit (Dead Strip): Some units contain a thermal fuse or internal disconnect mechanism that trips when the MOV overheats, cutting power completely so the strip goes dead (no power to the appliance at all) rather than leaving it vulnerable. [1]
    • Indicator Lights: Quality surge protectors usually feature a "Protected" or "Ground" status light. If that light turns off—or if you smelled burning or noticed tripped components after a storm—the unit is compromised and should be replaced immediately. [1, 2, 3]
     
    Last edited: Nov 16, 2026 at 1:01 PM
    IHATEPROPANE, BHags and brenndatomu like this.
  3. don2222

    don2222

    Joined:
    Nov 10, 2013
    Messages:
    3,448
    Likes Received:
    4,897
    Location:
    Salem NH
    Hello
    Also good backup to have whole house surge breakers too. :)
    Pic 1 - Circuit Panel with 2 Surge protectors with green LEDs for each 110 VAC leg and 30 Amp mechanical Interlok breaker for the generator.
    Pic 2 - Current monitors for each 110 vac leg, so I do not overload the generator.
    Note:
    The green LED lights on Eaton surge protective devices and surge breakers (such as the CHSPT2 or BR surge series) indicate that the internal surge protection elements are active and functioning normally
     

    Attached Files:

  4. don2222

    don2222

    Joined:
    Nov 10, 2013
    Messages:
    3,448
    Likes Received:
    4,897
    Location:
    Salem NH
    Hello
    Wow! I just looked up a dim green LED light on a surge breaker! So it is good to keep an eye on them too!
    A dim green LED on a surge-protective circuit breaker or whole-home surge protector usually means the device is degrading or nearing the end of its useful life after absorbing electrical surges. It can also point to a loose connection, wiring issue, or phase/power problem, or simply be how a specific model's indicator behaves
    Therefore it looks like a surge breaker’s dim green light means it took a lot of hits and needs replacing!
     
    Last edited: Nov 18, 2026 at 9:38 AM