In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Chainsaws tune up

Discussion in 'Chainsaws and Power Equipment' started by Ctwoodtick, Jun 6, 2026.

  1. Ctwoodtick

    Ctwoodtick

    Joined:
    Jul 4, 2016
    Messages:
    834
    Likes Received:
    5,838
    Location:
    Southeast ct
    Hi all,
    It’s been a bit since I’ve on the forum. Still chugging away with wood and well set up for next year or 2 for dry wood.
    I wanted to ask what you all do for chainsaw tune up. I have the echo 4920 which is a decent but I don’t think professional saw. I just replaced the spark plug , air and fuel filters. Do you guys do anything else?
     
  2. The Wood Wolverine

    The Wood Wolverine

    Joined:
    Aug 23, 2015
    Messages:
    18,731
    Likes Received:
    120,386
    Location:
    Gettysburg, PA
    When I replace fuel filters, check the fuel line condition. I keep extra on hand in case it needs refreshed.

    Good to see you visiting the club Steve.
     
  3. buZZsaw BRAD

    buZZsaw BRAD

    Joined:
    Feb 14, 2019
    Messages:
    34,401
    Likes Received:
    212,580
    Location:
    North Haven, Connecticut
    More or less the same. Digging into them not my thing.

    IF I was ever motivated enough I'd probably clean the inside real good...if that is.

    Great to hear from you Steve. Stop in more often!
     
    metalcuttr and T.Jeff Veal like this.
  4. Ctwoodtick

    Ctwoodtick

    Joined:
    Jul 4, 2016
    Messages:
    834
    Likes Received:
    5,838
    Location:
    Southeast ct
    Thanks guys!
    Fuel line looked good. Saw only about 18 months old. Trying to be better with maintenance
     
  5. wiguy

    wiguy

    Joined:
    Aug 7, 2025
    Messages:
    148
    Likes Received:
    926
    Location:
    Wisconsin
    I think most fuel filters can go a handful of years, one can test, blown through them. I think many remove a spark arrestor, if it’s in the muffler I’d check it once in a while. If they get plugged, can really bog down the engine.

    I flip the bar fairly often, mostly in conjunction with a chain switch. I recently sharpened a chain, usually in my vise, two teeth at a time with a round file. I squirt some grease in the bar holes, when I think about it.
     
  6. RCBS

    RCBS

    Joined:
    Jan 22, 2016
    Messages:
    6,148
    Likes Received:
    30,382
    Location:
    Over here
    I like to occasionally open the saw up a bit and clean out the grunge. I'll pull the recoil and clutch/bar plate to get that stuff the air gun normally misses or can't get. To justify the extra work I tell myself I'm making the saw lighter. :thumbs: Good time to visually inspect as well.
     
  7. Highbeam

    Highbeam

    Joined:
    Jun 25, 2014
    Messages:
    1,960
    Likes Received:
    6,332
    Location:
    Cascade Foothills, wet side of WA
    Keep it clean. I use an air nozzle to blow everything out of every nook and crannie I can get to. I dump the fuel and bar oil out, run the saw until it dies so a dryish carb before storage. Honestly with a sharp chain you can go a long time before messing with the air filter, I've never replaced an air or fuel filter and that's with a 5-10 cord per year habit.
     
    Ctwoodtick, Stephiedoll, RCBS and 3 others like this.
  8. CarharttWoodsman

    CarharttWoodsman

    Joined:
    Nov 17, 2023
    Messages:
    29
    Likes Received:
    269
    Location:
    Michigan
    I’ve also knocked some buildup off the spark plug with a wire brush every so often and flattened the bar and knocked the burr off one side if it is starting to fold over.
     
    JD Guy, RCBS, eatonpcat and 1 other person like this.