What's up today (bullchiting) thread.

The Kubota L4310 was made from 1998-2002. I think this one is a 98 .? So about 21 years old.

They couldn’t guarantee the hours. Meter says 1740ish. Meter works. When I bought it it had about 35 hours less than it does now. It runs great. Starts at the turn of the key. Farmer traded it in on a new cab Kubota. Dealer said farmer left tractor in barn with cows, and other animals. Might be why it’s all banged up. I’m sure it’s also from the work it’s done. It’s a little rough. Some things need adjusting, tightening, etc. As I have time I’m tinkering on little improvements here and there.

 

Looks safe enough

 

Link?

 

Should be, yeah

 

Will be the exact same. The cab from 73-80 was exactly the same. Minor trim interior and dash were different. The cab was a little bigger I think in the mid 80s but from 81-87 most everything on trucks and blazers was the same. And blazers and burbs continued the square untill 91. That said all floor mats from 73-87 truck and up to 91 for blazers and Burbans are the same.

My truck is an 80. Kind of a redheaded step child. Some say better some say worst. Was the first year to have the NP 205 PART TIME CASE. The last year for a 12 bolt in a half ton. Last year for the sought after buldge as I call them front fenders. Only year with single square headlights with turn signal in the bezel. Had a one off grill for that year only. Last year of a hood with cowl all in one. The next year the fenders changed to that slanted style, hood was a bit more sloped and cowl was now separate from hood. Truck was 300 pounds lighter. Way more than you want to know I know.

 

No, the tons of them that are making a lot of money because they have to after their 100k+ of education..

 

That’s one purty cat, Skeeter.

 

Good for the most part Woodlands. Battling some health issues which come getting , but make the best of it as it beats the alternative. Had to give up the competitive Trap Shooting so bought a small fishing boat and started fishing again. Thanks for the inquiry.

 

Replaced most of the tines on the York Rake yesterday. Except the two that I can’t get the bolt out of. I’ll have to separate the whole bottom part to get the center ones replaced. That will be some day when it’s raining out and I’m on a day off. Then I went and raked all the rough spots and got them leveled off nice. Then pulled a few more stumps with the 310J. And went in and worked a couple hours of OT. Took the evening off and relaxed with the family. A good day.

Looks like another beautiful day out there today. Going for a ride on the wheelers for a bit this morning before I have to go into work. I hope all of you have a great day today. The beautiful summer weather is finally here!

 

Day two on siding repairs. The old door had foil tape for a drip edge over the top trim of it. I ended up taking the old unused door out and put a window in. Too many things wrong, and it made sense to start fresh. Cedar clapboards were installed with wrong nails, many of them split and they also didn't line up across from the old door. Little details bother me when it comes to craftsmanship.

 

What I'm doing this afternoon

 

Dang, where did the day go? One more bundle of 8's and that should get me over the window.

I was in the sun most of the day until 2pm when the shade made it around the back.

 

Enjoy

 

Guess he's got some 'splaining to do.

 

Had a busy day yesterday. campinspecter was staining replacement doors and I scrubbed the back porch and one wall of siding on the house. I even got some sewing done and then we watched the Home Run Derby. Quite the performance. I don't think I have ever watched that before. Off to the big smoke for shopping and dog teeth cleaning today.