In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Plumbing the depths..

Discussion in 'The DIY Room' started by Chaz, Apr 1, 2018.

  1. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    Of my sanity. :loco: :crazy:

    OK, so I initially imagined this thread about building a box. Not a typical box, but a box to house a dishwasher.

    Jill said she wanted a dishwasher, and as she's on O2, and limited in stamina these days, it seems a worthwhile investment. So, I go buy a dishwasher. It got delivered just under 2 weeks ago, so last weekend and this weekend have been "adventurous".

    So, I check dimensions of the side panels, back, top and bottom.
    Alright.. off to Home Depot I go. I determine that particle board will end up being the build material.
    Not that I like particle board, but the woodshop is not operational yet, so actual wood will have to wait.

    I get the particle board, and have it cut to the dimensions I've written down. Pick up other supplies and home I go.

    Time to start working on the box.
    box1.jpg

    Guess it could use more sides to make it a proper box.:picard:

    box2.jpg

    This shows that I did think about elec and water, and drain lines. Yeah!!:thumbs::thumbs:

    Still needs more sides.

    box3.jpg
    We're getting there..
    They say the dishwasher should not sit on the floor, or carpeting.. ok.
    box4.jpg

    They sell plywood at Home Depot also. ;)

    Let's see how the dishwasher fits before we go to far eh??

    test-fit.jpg

    Not too shabby.. so far, so good.. I have 3 sides, and a bottom. Now.. what about a top??

    hmmm-a-touch-small.jpg

    Uhmmm.. that don't look right.
    Guess I shoulda considered the other 3/4" on each side huh??:doh:

    Well, this isn't the end of the world, just some "leftover" material for a different project someday.

    Let's see how things might look when done. Shall we?

    test-fit2.jpg

    Not terrible.. but something seems off..

    oops.jpg
    Well that looks like crap. :hair:
    Looks like it's time to pull everything back out and make some corrections.

    I'll add more tomorrow, as this post is getting as lengthy as the dishwasher install.

    Not to worry, things get WAY more interesting later. :whistle:;)
     
  2. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
  3. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,772
    Likes Received:
    145,430
    Location:
    Coastal South carolina
    I'd be tempted to put a similar stain color/paint on the exposed plywood as your counter top, or a laminate strip and call it done.

    PS, we had our hot water heater turned up very high before we were blessed with a lil one late in life, it was very helpful doing dishes and other tasks with my limited stamina and physical limitations. It will be turned up back to very high temp again when she is old enough to not scald herself-back then it made doing dishes much easier for me.
     
  4. Canadian border VT

    Canadian border VT

    Joined:
    Feb 18, 2015
    Messages:
    19,814
    Likes Received:
    132,134
    Location:
    Vermont
    I would get a piece of counter top and throw it over both.. More counter space..
     
  5. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    Yep.. you have echoed one of my many statements during this process. :whistle:

    Have to admit I thought of that, but dismissed the idea. I have other plans for kitchen upgrades in the future, I'll live with a 'certain amount' of ugliness for now.

    I have the water temp set at around 130F. I like hot water, but yeah, it can get hot enough to pretty much scald someone. Fortunately no kids around to worry about.

    So.. did a lot of work this past weekend, but didn't take any pics. :rolleyes:
    Took some of the nearly finalized project tonight.
    Didn't post last night as I had some other pressing issues to tend to, and sometimes there's never enough hours in the day.

    So.. here goes.

    dw-top-1.jpg

    Used a piece of the pallet material that the IS was shipped in as a top brace. I didn't think it would "secure" to the cabinet well enough with the thin metal strapping supplied. The board has 2 2" screws predrilled and installed on each side, with 3 small 3/4" screws securing the diswasher from the front.
    I also installed 1 2" screw on each side of the base, securing the bottom of the DW to the sides of the cabinet. Those should keep it from rocking and/or wiggling forward.

    Speaking of the bottom.. that needed cleaned up.

    dw-side-1.jpg

    It now matches up with the cabinet much better. :yes:

    Had issues with the power cord not reaching where I intended to install the outlet, so another modification was made.

    dw-side-2.jpg

    Drilling and opening up an exit near the power connection allowed for an additional 6 or 7 inches of cord available. Much betterer.:thumbs:

    Well Canadian border VT , I'm likin' the way you're thinkin'.:sherlock:
    How's about this??

    counter-1.jpg

    It still needs leveled and some supports at the wall end, but put it on for pic taking.

    Something still is off though, as you can see, I decided for cord length to the outlet to move the DW to the right, leaving a hole in the center. Guess another box project will be in order.

    I'm thinking of making a tall rectangular section to go between the cabinet and DW, and have a slide out drawer/door to be used for cutting boards and such.

    It won't be able to be as deep as the cab. or DW as the 220 line for the stove comes out of the wall in the back.

    box-pt-2.jpg

    And finally, at some point I'm gonna get rid of the gawdawful carpet in there.
    They simply laid carpet on top of the cement slab foundation, so it kinda blows in wintertime when in socks.:shiver:

    I also want to reface all of the cabinetry with Black Walnut board that I had made last year. This is a LARGE part of the reason I talked Jill into letting me spend the $$ to get the equipment to setup a woodworking shop. Once finally all setup and running, I will start on the cabinetry project.

    Finally, the project is pretty well done for now, and Jill did the first load of dishes in it today. :dancer::rootintootin::dennis::cheers:


    Next post.. the "interesting bits"...:bug:
     
  6. Canadian border VT

    Canadian border VT

    Joined:
    Feb 18, 2015
    Messages:
    19,814
    Likes Received:
    132,134
    Location:
    Vermont
  7. Woodwidow

    Woodwidow

    Joined:
    Oct 4, 2013
    Messages:
    15,617
    Likes Received:
    96,165
    Location:
    Port McNeill, BC Northern Vancouver Island
    I appreciate the progression of pictures in your post. Looks good for making do. You both will really appreciate the dishwasher.
     
  8. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    Thank you both, I appreciate it. I'm definitely not planning to become a kitchen cabinetry contractor by any stretch of the imagination, fortunately. ;)

    As to the fronts of the particle board not being dressed up at all, I think I like that better than the grey that they painted the cupboards. :wacky:

    Let's just say that I'm not quite up to the aesthetics portion of the work just yet. I'm hoping that next year will show a whole new look for the kitchen. I'd ultimately like to insulate and put new flooring down, replace all the paneling as well as adding more elec outlets, and redoing the ceiling with more LED lighting.

    The biggest obstacle will be the sink. I dislike the huge monstrosity, but Jill likes it.. it adds "rustic charm". :picard:

    To be honest, she is correct, but the whole "rustic charm" thing is a bit overrated in my opinion, and the thing is almost impossible to work around to create the kitchen I'd prefer.
    Not to mention the ceramic is chipped in areas, and pitted from decades of use.

    OK, so on with the install fun and games.

    As everyone knows, a dishwasher needs electrical, water source, and a drain connection.

    Well, I'm not really a plumber, but I can generally manage things when I have to.
    So, during one of the initial trips to Home depot, I pick up a collection of bits for plumbing the DW. I get a shutoff valve, a CPVC tee fitting, and a collection of parts to manage the drain which is sched 40 PVC. They don't carry a sched 40 appliance wye connector, and I didn't feel like waiting for one to ship if ordered online, so I got a wye fitting, a threaded female/male union piece, and a male/male threaded piece to attach the drain hose to.

    First, the assembled bits of the drain.
    drain-line.jpg

    all cut and glued into place, The bit on the cab bottom is from a very old leak at the trap fitting as can be evidenced on the trap itself.

    I removed everything from the trap to the sink, then cut and glued in the fittings for the drain line, then reinstalled assembled parts. I used teflon tape around the threads on the sink exit.
    The DW came with spring clamps for the drain line, but I prefer to use the screw clamps as I tend to trust them much more than spring clamps.

    Now for the water supply.

    Pic of water lines originally..
    water-lines1.jpg

    The house was/is plumbed odd, as they came through the cinderblock wall from the pump room and fed directly to the sink, then ran shutoffs that feed the bathroom and laundry.
    There was NO shutoff out in the pump room for the cold water, but did have one for the hot water supply. No clue why on one and not the other, but that was corrected some years back when the garden hose supply line broke. Since I had the house water shutoff, I installed a shutoff into the cold water supply.

    I cut and glued in the tee fitting, using the small bit of cut out pipe for the connection point for the DW supply shutoff.

    water-lines2.jpg

    I had done the plumbing connections prior to last weekend, this pic was taken on Sunday afternoon, things were looking good at that point. Had no leaks in water lines, or the drain lines. All set to install and test the DW.

    So, I get the DW in place, and plug it in, set it do a 1 hour run just as a test.
    It makes some noise, but isn't doing anything.. odd.
    I also hear the water pump running, and I remember that the DW needs a certain amount of water pressure to run properly, so I figure I'd wait a minute or so.

    Well, I hear something odd, and think maybe the toilet was running as it sometimes does.
    I go to the bathrooom, and find that it's getting flooded with nice warm water. :faint:

    I run back to the kitchen and shutoff the hot water.
    Go back to the bathroom and find that a hot water line tee had blown out. :mad:

    So, I grab a towels and start sopping up the water, then I hear a roar on the wall.
    Huh??

    Rush out to the kitchen and see cold water line blew out right BEFORE the shutoff and is blasting all over the corner. :mad::mad:

    So, now I run outside and close the shutoffs, and decide to close the water main as well.. just in case.

    So, now I've got 2 messes to clean up. Not exactly the Easter Sunday I'd had in mind.

    I clean up the messes, and look to reglue the joints that just burst.
    Hot water tee in bathroom refuses to stop leaking, finding a leak in the corner of the joint I figure it's trashed. So I run back down to HD, and find they're closed for the night.
    :faint:

    So, now it's sunday night, we've got no hot water in the bathroom, and I've gotta shower before work on Monday. So I decide that I will clean the tee fitting as best I can, prime it, and then slather the heck out of it with the glue and let it dry overnight. Either I can take a shower, or I call the boss and say I'll be in after lunch.

    Monday morning, turn on the hot water, and it's dripping, just a small leak so I quick shower, and shave then turn the water back off.

    After work on Monday, I once again head to the Depot and pick up union fittings, tee fittings, and 90° fittings to replace the leaking section, as well as to redo a couple of other fittings they seemed to have decided to add for fun I guess.

    Bottom line, I hate doing plumbing. :rofl: :lol::rofl: :lol:

    Pic of where things blew out, in comparison to the joints I added.

    water-line-breaks.jpg
    Oh, and I know I had posted some of this in Pallet Pete 's trailer build thread and was advised on the 'proper' cure time for the CPVC glue, I just couldn't let it go longer than 2 hours on Monday after getting things put back together. Things are holding fine, but I do understand that the connections were not fully cured at that point, but strong enough to hold.

    I will re-emphasize that the connections that blew out, were ones that were made some decades ago, not the fresh ones I'd made. I figure that what wiggling of the pipe that I did during my work must've worked the other connections loose after all these years.

    But, it does reinforce my decision to replumb the entire house with clamped PEX pipe at some point in the near future. Hopefully with a more logical layout of the lines, and easily accessible shutoffs.
     
    Shawn Curry, Eric VW and Pallet Pete like this.
  9. Pallet Pete

    Pallet Pete Moderator

    Joined:
    Oct 2, 2013
    Messages:
    13,483
    Likes Received:
    54,125
    Location:
    Ovid
    Love the pictures!​
     
    Canadian border VT, Eric VW and Chaz like this.
  10. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    Did they crack? If they just blew off then its a safe bet they were never glued right in the first place...probably no primer. If they cracked or just broke, then yeah, just old and brittle
    Good job with the stick-to-it-iveness! :yes:
     
  11. Pallet Pete

    Pallet Pete Moderator

    Joined:
    Oct 2, 2013
    Messages:
    13,483
    Likes Received:
    54,125
    Location:
    Ovid
    Do your self a favors and buy the ratchet stainless pex crimps and crimped your arms will thank you for it! Also use a LOT of anchors for the pex it likes to move around and that will eventually make the connections leak a little. As long as you do those steps pex lasts a very long time!
     
  12. Pallet Pete

    Pallet Pete Moderator

    Joined:
    Oct 2, 2013
    Messages:
    13,483
    Likes Received:
    54,125
    Location:
    Ovid
    Man I hate those plastic shutoff valves. If you can get 1/4 turn metal shutoff valves they last much longer and shut off easily 1/4 turn and off...
     
  13. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    I actually think it was a bit of both. The tee in the bathroom blew off, and it may have cracked when I was trying to reglue-refit it to the line.

    As to the cold water line, blew out of the shutoff clean as a whistle.
    Could not see or feel any glue, but I wouldn't think it would stay together all these years without glue.

    As to stick-to-it-iveness, I don't figure I was given much choice in the matter. ;)

    Pallet Pete thanks for the advice on the PEX, I agree on the anchors as well, they didn't put as many as they should on the CPVC here, and it sags pretty bad in spots. One of the reasons I know this plumbing is way dated, and really in need of replacement.

    I will definitely look for a ratchet crimper as well. :yes:
    Sounds much gooder.
     
    Eric VW likes this.
  14. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    For low pressure, or drain lines like that, I have better luck with spring clamps. There's a reason that OEM VERY rarely use worm drive hose clamps on anything...pretty high failure rate.
     
    Eric VW, Pallet Pete and Chaz like this.
  15. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    I can still use the spring clamps, I guess I didn't think about the low pressure of the drain system.
    If you think the metal clamps will give me headaches, I will take that under advisement.
    Thx.:yes:
     
    Eric VW and Pallet Pete like this.
  16. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    That clamp should be fine there...just in general I usually try to avoid them in most places. They do work good for some things though...
     
    Eric VW, Pallet Pete and Chaz like this.
  17. Eric VW

    Eric VW Moderator

    Joined:
    Jan 6, 2015
    Messages:
    24,572
    Likes Received:
    141,785
    Location:
    US
    Wow Chaz..... serious piping debacle!:faint:
    Glad you’re over the most of it:handshake:

    PEX is King!:yes:
     
    Pallet Pete, brenndatomu and Chaz like this.
  18. Chaz

    Chaz

    Joined:
    Jan 27, 2018
    Messages:
    8,755
    Likes Received:
    62,099
    Location:
    Southwestern NY
    Yeah, let's say I was "less than pleased" during the problems.:hair:

    I don't necessarily handle these things with "grace" as I would prefer, and I usually look back and realize that I over-reacted emotionally :mad: to the situation.

    It's after that point that I can generally see the humor in the situation. :whistle:

    As I've said previously, I'm a work in progress.
    It should prove interesting to see the finished product that is me. :eek:
     
  19. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    Aren't we all brother, aren't we all...:yes:
     
  20. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,772
    Likes Received:
    145,430
    Location:
    Coastal South carolina
    :thumbs:

    Those sinks are a kind of a hot ticket out here, there aren't many around like I heard there are out in the colonial states, both them and the new ones are expensive but new ones do not have history like your does!
     
    Last edited: Apr 5, 2018