In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Get rid of one project, end up buying another....lmao

Discussion in 'Chainsaws and Power Equipment' started by Scotty Overkill, Apr 28, 2017.

Page 1 of 3
  1. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,614
    Likes Received:
    64,517
    Location:
    Central PA
    Sold my Stihl 020T the other day to blacksmith, I'm just tired of dumping money in it and sold it to him for what I had invested in just the new parts alone. After running his a few times, I'm just not all that impressed with the 200T series in general. Yes they have good power and balance, but they are expensive to purchase, repair, and replace parts on, they are gas hogs when you're up the tree, and man can that get annoying. I'm quite happy with my Echo CS355T, it's served me faithfully and well. Dollar for dollar I can buy two of those for the cost of ONE 200T. So, the other day a buddy of mine who picks barns and garages and yard sales texts me and says "hey, would you be interested in this saw? It's in parts, make me an offer".

    After looking at the pics, I threw a $40.00 offer at him and he took it. From what I can tell, it may just need a P/C.

    received_1517167101658842.jpeg

    received_1517225131653039.jpeg

    received_1517225224986363.jpeg

    received_1517225248319694.jpeg

    received_1517243564984529.jpeg

    One brand new and one slightly used chain, decent bar, heck. That stuff alone is worth 40 bucks! I'll break it all down and do a hydrosonic bath for her, and go from there......

    Just what I needed.....another project!!
     
    Scotty Overkill, Apr 28, 2017
    #1 Top
    Stephiedoll, Andrew9802, dougand3 and 18 others like this.
  2. Barcroftb

    Barcroftb

    Joined:
    Sep 30, 2015
    Messages:
    3,087
    Likes Received:
    17,935
    Location:
    The Mitten
    For 40 bucks that's a you suck get Scott! Those are rock solid saws! Put me down as another happy echo 355t user as well!
     
    Barcroftb, Apr 28, 2017
    #2 Top
    Eric VW, blacksmith, Horkn and 9 others like this.
  3. thistle

    thistle

    Joined:
    Oct 4, 2013
    Messages:
    2,736
    Likes Received:
    9,753
    Location:
    Polk/Guthrie Counties,IA
    I've always said if my 35 yr old Echo 280E top handle ever dies.I'll replace it with the 355T.

    My problem is I just keep adding future projects to the stable,though I've completed quite a few now there's still more that aren't....;) :rofl: :lol:
     
    thistle, Apr 28, 2017
    #3 Top
    Eric VW, blacksmith, Horkn and 7 others like this.
  4. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,433
    Likes Received:
    103,363
    Location:
    St. Lawrence River Valley, NY
    Keep ya outta trouble.:whistle:
     
    Gasifier, Apr 28, 2017
    #4 Top
    FatBoy85, Eric VW, blacksmith and 10 others like this.
  5. chris

    chris

    Joined:
    Oct 9, 2013
    Messages:
    3,149
    Likes Received:
    11,152
    Location:
    SE WI
    sorta like a honey do list -never ending
     
    chris, Apr 28, 2017
    #5 Top
    Eric VW, blacksmith, savemoney and 7 others like this.
  6. Screwloose

    Screwloose

    Joined:
    Jan 15, 2017
    Messages:
    5,357
    Likes Received:
    31,288
    Location:
    SE Wisconsin
    I love my 355 ..... First and only saw with a clutch driven oiler I've ever used. I wish all my saws had that. It even survived being a wheel chock once.
     
    Screwloose, Apr 28, 2017
    #6 Top
    Eric VW, blacksmith, Horkn and 3 others like this.
  7. thistle

    thistle

    Joined:
    Oct 4, 2013
    Messages:
    2,736
    Likes Received:
    9,753
    Location:
    Polk/Guthrie Counties,IA
    Kinda does.:yes: Most days I'm too tired anymore to get in very much.:D And lots of the weekends I don't work is usually spent relaxing & resting up for the week ahead.
     
    thistle, Apr 28, 2017
    #7 Top
    Eric VW, blacksmith, savemoney and 7 others like this.
  8. Screwloose

    Screwloose

    Joined:
    Jan 15, 2017
    Messages:
    5,357
    Likes Received:
    31,288
    Location:
    SE Wisconsin
    Can someone school me on what a "electronic quickstop" is ?
     
    Screwloose, Apr 28, 2017
    #8 Top
    savemoney, Horkn and wildwest like this.
  9. BuckthornBonnie

    BuckthornBonnie

    Joined:
    Oct 4, 2013
    Messages:
    974
    Likes Received:
    3,207
    Location:
    Penn Yan, NY
    Sweet. Post a wanted ad for an 036 top end or just cylinder. Meteor has a very good piston for $34ish.
    AM seals are fine for this series. Replace the impulse (3"? Section of oem line...not molded... could use tygon). Oem fuel line is best but check diameter of hole in tank--- may not accept the 036 line but that can be changed.
    Air filter is older style. As is tank vent.
    Nice saws for sure.
     
    BuckthornBonnie, Apr 28, 2017
    #9 Top
    Eric VW, blacksmith, Horkn and 3 others like this.
  10. BuckthornBonnie

    BuckthornBonnie

    Joined:
    Oct 4, 2013
    Messages:
    974
    Likes Received:
    3,207
    Location:
    Penn Yan, NY
    Bearings can spin in the case on pto side but that's rare. Wiggle that crank. Case gasket near the muffler can weaken and weep oil. Tighten case screws and put heat tape on after rebuild (before installing muffler).
     
    Last edited: Apr 28, 2017
    BuckthornBonnie, Apr 28, 2017
    #10 Top
    Eric VW, blacksmith, Horkn and 2 others like this.
  11. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,614
    Likes Received:
    64,517
    Location:
    Central PA
    Electronic ignition, quickstop equipped (clutch brake)
     
    Scotty Overkill, Apr 28, 2017
    #11 Top
    Eric VW, blacksmith, savemoney and 5 others like this.
  12. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,614
    Likes Received:
    64,517
    Location:
    Central PA
    definitive dave has the P/C I need in his ebay store, I'm gonna go ahead and get it off of him. I'll break it all down first for a hydro bath, and make sure I order everything I need.

    This will be a good bucking saw for the 20" bar.....
     
    Scotty Overkill, Apr 28, 2017
    #12 Top
    Eric VW, blacksmith, savemoney and 3 others like this.
  13. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,151
    Likes Received:
    141,430
    Location:
    Wyoming high plains
    I just googled that. :rolleyes: All those years we rolled coffee cans filled with our bird's seed husks under our feet while watching tv to clean empty brass bullet things, :picard:
     
    wildwest, Apr 28, 2017
    #13 Top
    FatBoy85, blacksmith, Eric VW and 3 others like this.
  14. BuckthornBonnie

    BuckthornBonnie

    Joined:
    Oct 4, 2013
    Messages:
    974
    Likes Received:
    3,207
    Location:
    Penn Yan, NY
    Oh yeah, you're going to like it. What brand p/c from his store? The Farmertec is the lower price point; I haven't used one for this saw yet. The NWP is slightly higher quality (usually) with better plating. My Hyway is close to the NWP.
    Caber rings are a nice upgrade as a lot of pro guys wear the cheap rings down to a noticeable drop in comp.
    The circlips are problematic for both so Dave may toss in oem.
     
    BuckthornBonnie, Apr 29, 2017
    #14 Top
    Scotty Overkill, blacksmith and savemoney like this.
  15. BuckthornBonnie

    BuckthornBonnie

    Joined:
    Oct 4, 2013
    Messages:
    974
    Likes Received:
    3,207
    Location:
    Penn Yan, NY
    The control switch spring can wear but that's easy to replace. The oil line--- same as your 064. So, yea...fun to replace. I've been using stihl fuel line with a 1/8"spring inside it to prevent collapsing from heat. I dont have a lot of time on this setup tho...it cuts install time by more than half.
    After a lot of time on 034s we've said-
    20" on 034super, 036, 036 pro (all 48mm)
    18" on 034 (46mm)
    In hardwood with a decent chain, that is. softwood? both can handle 20" easily.
     
    BuckthornBonnie, Apr 29, 2017
    #15 Top
    Scotty Overkill and blacksmith like this.
  16. BuckthornBonnie

    BuckthornBonnie

    Joined:
    Oct 4, 2013
    Messages:
    974
    Likes Received:
    3,207
    Location:
    Penn Yan, NY
    Nice 036 cylinders for sale on ope. Throw in a $34 meteor from Dave and you're golden.
     
    BuckthornBonnie, May 2, 2017
    #16 Top
    blacksmith likes this.
  17. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,614
    Likes Received:
    64,517
    Location:
    Central PA
    Have a link?
     
    Scotty Overkill, May 3, 2017
    #17 Top
  18. Redfin

    Redfin

    Joined:
    Mar 1, 2015
    Messages:
    922
    Likes Received:
    4,268
    Location:
    central Pa
    Redfin, May 3, 2017
    #18 Top
    Scotty Overkill likes this.
  19. Redfin

    Redfin

    Joined:
    Mar 1, 2015
    Messages:
    922
    Likes Received:
    4,268
    Location:
    central Pa
    I just reread this thread. Yours isnt a super? Stroke is shorter if not.
     
    Redfin, May 3, 2017
    #19 Top
  20. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,614
    Likes Received:
    64,517
    Location:
    Central PA
    Mines just a standard 034, but I can use the 48mm p/c, can't I?
     
    Scotty Overkill, May 3, 2017
    #20 Top
Page 1 of 3