In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Nice Find....I hope

Discussion in 'Chainsaws and Power Equipment' started by M2theB, Apr 15, 2017.

Page 1 of 2
  1. M2theB

    M2theB

    Joined:
    Jan 13, 2017
    Messages:
    3,001
    Likes Received:
    19,196
    Location:
    Central Massachusetts
    IMG_0434.JPG IMG_0435.JPG On the way to the store I passed a chair and what looked like a saw below it at the end of a driveway. I turned around and got back to the spot and then saw the sign in the chair FREE.
    Back at the house i gassed it up and bar oil. 3 pulls and it turned over. On and off the choke and fired up. Real high rev and when I goosed it to calm it down it bogged under the trigger and died. Started right up again though. Similar thing.
    I'm going to mess with high and low tuning.
    Feel free to give me your thoughts.
    I'll report back on progress
     
    M2theB, Apr 15, 2017
    #1 Top
    Hammy, Will C, concretegrazer and 10 others like this.
  2. Ralphie Boy

    Ralphie Boy

    Joined:
    Oct 25, 2014
    Messages:
    4,274
    Likes Received:
    29,903
    Location:
    Rabbit Hash, Kentucky
    You got that big azz saw for free?!!?:faint:
     
    Ralphie Boy, Apr 15, 2017
    #2 Top
    Hammy, Eric VW, Chvymn99 and 3 others like this.
  3. papadave

    papadave

    Joined:
    Oct 3, 2013
    Messages:
    18,181
    Likes Received:
    82,470
    Location:
    Right where I want to be.
    Nice find, but...........you suck. :rofl: :lol:
    Man, some guys have all the luck.
     
    papadave, Apr 15, 2017
    #3 Top
    Hammy, Eric VW, Chvymn99 and 3 others like this.
  4. Horkn

    Horkn

    Joined:
    Dec 17, 2014
    Messages:
    28,531
    Likes Received:
    161,371
    Location:
    SE Wisconsin
    That was a score.

    It's probably a carb or fuel line simple issue.
     
    Horkn, Apr 15, 2017
    #4 Top
    Hammy, Eric VW, Chvymn99 and 3 others like this.
  5. MasterMech

    MasterMech The Mechanical Moderator

    Joined:
    Oct 2, 2013
    Messages:
    9,648
    Likes Received:
    26,024
    Location:
    Greenville County SC
    Make sure the muffler screws are tight on those.
     
    MasterMech, Apr 15, 2017
    #5 Top
    Hammy, Eric VW, Horkn and 3 others like this.
  6. Hydro Farmer

    Hydro Farmer

    Joined:
    Feb 18, 2015
    Messages:
    173
    Likes Received:
    459
    Location:
    Hinckley, MN
    Take the carb off spray it out with carb cleaner. Throw a new plug and air filter on.

    30 Clip Magazine On My Ghost Gun
     
    Hydro Farmer, Apr 15, 2017
    #6 Top
    Hammy, Eric VW, Horkn and 2 others like this.
  7. Hydro Farmer

    Hydro Farmer

    Joined:
    Feb 18, 2015
    Messages:
    173
    Likes Received:
    459
    Location:
    Hinckley, MN
    Another thing is start with fresh gas.

    30 Clip Magazine On My Ghost Gun
     
    Hydro Farmer, Apr 15, 2017
    #7 Top
    Hammy, Eric VW, Horkn and 1 other person like this.
  8. M2theB

    M2theB

    Joined:
    Jan 13, 2017
    Messages:
    3,001
    Likes Received:
    19,196
    Location:
    Central Massachusetts
    Tried to share a video but it must have been too big.
    Pulled and cleaned the filter and spark arrestor. Put Husq 50 mix in a can in. Tuned the idle first and got it to idle ok. A few iterations on the high and low settings. I got it to a point that just before it would die, I could back off on the trigger and keep it going. Kept doing that for a few minutes until I had it screaming, drop to idle and back up. I'd shut her off and quick start right after and right to idle. It's still a little dodgey coming out of the blocks, but that might be a fine tune. I think it just had bad fuel in it for too long. And yes, one of the muffler bolts is spinning. And it leaks bar oil pretty good.
     
    M2theB, Apr 15, 2017
    #8 Top
    Hammy, Eric VW, Horkn and 1 other person like this.
  9. Hydro Farmer

    Hydro Farmer

    Joined:
    Feb 18, 2015
    Messages:
    173
    Likes Received:
    459
    Location:
    Hinckley, MN
    Nice...

    30 Clip Magazine On My Ghost Gun
     
    Hydro Farmer, Apr 15, 2017
    #9 Top
    Hammy, Eric VW and Horkn like this.
  10. Hydro Farmer

    Hydro Farmer

    Joined:
    Feb 18, 2015
    Messages:
    173
    Likes Received:
    459
    Location:
    Hinckley, MN
    Where is it leaking bar oil?

    30 Clip Magazine On My Ghost Gun
     
    Hydro Farmer, Apr 15, 2017
    #10 Top
    Hammy, Eric VW and Horkn like this.
  11. M2theB

    M2theB

    Joined:
    Jan 13, 2017
    Messages:
    3,001
    Likes Received:
    19,196
    Location:
    Central Massachusetts
    Out of the oiler area, under the bar hold down plate
     
    M2theB, Apr 15, 2017
    #11 Top
    Hammy, Eric VW and Horkn like this.
  12. Chvymn99

    Chvymn99 Moderator

    Joined:
    Oct 4, 2013
    Messages:
    20,809
    Likes Received:
    109,312
    Location:
    KC Metro
    Nice find....:thumbs:...
     
    Chvymn99, Apr 15, 2017
    #12 Top
    Hammy, Eric VW and Horkn like this.
  13. bogydave

    bogydave

    Joined:
    Oct 8, 2013
    Messages:
    10,313
    Likes Received:
    37,218
    Location:
    Alaska, North of Anchorage & South of Fairbanks
    !!!!!!!!!!!Nice SCORE !!!!!!!
    :thumbs:
     
    bogydave, Apr 15, 2017
    #13 Top
    Hammy, Eric VW, Chvymn99 and 1 other person like this.
  14. M2theB

    M2theB

    Joined:
    Jan 13, 2017
    Messages:
    3,001
    Likes Received:
    19,196
    Location:
    Central Massachusetts
    It needs more love for sure. Or better cleaning. After it sits for 10 minutes or so and cools down it goes back to hard to getting it up to full speed. I have to baby it past the stall point. But after I do, it screams at the top, goes back to a nice idle and back to the top without issue.
    The one thing I did notice that all look into is that it has "Air Injection" on the sticker. I've never seen that before.
     
    M2theB, Apr 15, 2017
    #14 Top
    Hammy, Eric VW and Horkn like this.
  15. MasterMech

    MasterMech The Mechanical Moderator

    Joined:
    Oct 2, 2013
    Messages:
    9,648
    Likes Received:
    26,024
    Location:
    Greenville County SC
    Air injection, while cool tech and all, is fancy marketing wank for pre-cleaning the air before it sees the actual air filter.
     
    MasterMech, Apr 15, 2017
    #15 Top
    Hammy, cnice_37, Eric VW and 2 others like this.
  16. M2theB

    M2theB

    Joined:
    Jan 13, 2017
    Messages:
    3,001
    Likes Received:
    19,196
    Location:
    Central Massachusetts
    So it is not some gizmo that could have gone south and be part of its problem?
     
    M2theB, Apr 15, 2017
    #16 Top
    Hammy, Eric VW and Horkn like this.
  17. MasterMech

    MasterMech The Mechanical Moderator

    Joined:
    Oct 2, 2013
    Messages:
    9,648
    Likes Received:
    26,024
    Location:
    Greenville County SC
    Not a single moving part. ;)
     
    MasterMech, Apr 15, 2017
    #17 Top
    Hammy, cnice_37, Eric VW and 2 others like this.
  18. MasterMech

    MasterMech The Mechanical Moderator

    Joined:
    Oct 2, 2013
    Messages:
    9,648
    Likes Received:
    26,024
    Location:
    Greenville County SC
    If I remember right, these had a plastic clamp on the carb boot that was problematic?
     
    MasterMech, Apr 15, 2017
    #18 Top
    cus_deluxe, Mag Craft, Hammy and 7 others like this.
  19. Horkn

    Horkn

    Joined:
    Dec 17, 2014
    Messages:
    28,531
    Likes Received:
    161,371
    Location:
    SE Wisconsin
    If that's the case, a simple metal hose clamp should fix it. No?
     
    Horkn, Apr 15, 2017
    #19 Top
    Hammy and Eric VW like this.
  20. MasterMech

    MasterMech The Mechanical Moderator

    Joined:
    Oct 2, 2013
    Messages:
    9,648
    Likes Received:
    26,024
    Location:
    Greenville County SC
    Better yet, Husky puts out a metal clamp to replace it with but I have no idea what the part number is. Ask anybody with a 346XP. Browse 346XP or 345/350 build threads it shouldn't take long to stumble across it.

    Standard worm drive clamps are horrendous at sealing. The proper clamp works just a tad differently.
     
    MasterMech, Apr 15, 2017
    #20 Top
    Hammy, Warped5 and Eric VW like this.
Page 1 of 2