In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

it's been a while....

Discussion in 'Chainsaws and Power Equipment' started by old 040, Dec 23, 2015.

Page 1 of 3
  1. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    after selling off several saws over the last few months, been kinda on the look out for sump'n i haven't owned but always wanted to, so a couple days ago this echo cs4600 popped up on c-list on the cheap and close by, a saw i've wanted but just never came across at the right deal at the right time until today, finally hooked up with the seller and home it came in non running condition but still had very good compression and is complete, i found that the choke rod had dislodged and for the most part that's all that was wrong with it, had it running in less than 20 minutes......:).......sometimes referred to as the poor mans 346xp, this saw seams to run very well, and i can tell with a MM and just a good cleaning this should be a great firewood saw, pretty happy so far......:D.........the pic is the one the seller posted...... 00202_ifrTyUwWTH4_600x450.jpg
     
    old 040, Dec 23, 2015
    #1 Top
    HDRock, Moparmyway, Jack Straw and 9 others like this.
  2. bobdog2o02

    bobdog2o02

    Joined:
    Nov 19, 2015
    Messages:
    3,005
    Likes Received:
    10,407
    Location:
    Drury Lane, PA
    Nice buy. Have fun
     
    bobdog2o02, Dec 23, 2015
    #2 Top
    Eric VW, HoneyFuzz, Horkn and 1 other person like this.
  3. Barcroftb

    Barcroftb

    Joined:
    Sep 30, 2015
    Messages:
    3,086
    Likes Received:
    17,929
    Location:
    The Mitten
    That's some cool old echo iron! There is a lot to like about them. Have fun with it.:saw:
     
    Barcroftb, Dec 24, 2015
    #3 Top
    Eric VW, HoneyFuzz and old 040 like this.
  4. HoneyFuzz

    HoneyFuzz

    Joined:
    Jan 20, 2014
    Messages:
    4,484
    Likes Received:
    14,831
    Location:
    Northeast , Ohio
    Good deal there buddy !!! Enjoy :)
     
    HoneyFuzz, Dec 24, 2015
    #4 Top
    Eric VW and old 040 like this.
  5. AJtree88

    AJtree88

    Joined:
    May 15, 2014
    Messages:
    318
    Likes Received:
    1,764
    Mark, I just picked one up a few months back. Let me know if you're interested in having a twin.
     
    AJtree88, Dec 24, 2015
    #5 Top
    old 040 and Eric VW like this.
  6. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,421
    Likes Received:
    103,250
    Location:
    St. Lawrence River Valley, NY
    Nice! I like my Echos.:saw:
     
    Gasifier, Dec 24, 2015
    #6 Top
    old 040 and Eric VW like this.
  7. Eric VW

    Eric VW Moderator

    Joined:
    Jan 6, 2015
    Messages:
    24,398
    Likes Received:
    140,388
    Location:
    US
    I have the same palm sander.....
    Good lookin saw- when will we see YOUR pic of it?
     
    Eric VW, Dec 24, 2015
    #7 Top
    old 040 likes this.
  8. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    hmmm...........shoot me over a PM and some pics if you can........:)
     
    old 040, Dec 25, 2015
    #8 Top
    HoneyFuzz likes this.
  9. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    soon......already did Christmas yesterday evening.......so i may have time to shine it some today!..........:)
     
    old 040, Dec 25, 2015
    #9 Top
    Eric VW likes this.
  10. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    O.K., you got pics.......well, this being my first of this series of echo, i'll give you guys my highs and lows on this saw, tore it down to the crankcase assy, gave it total cleaning that always takes up most of the time, built much like a husky 1 or 2 series saw, these are closed port cylinder saws, went ahead and deleted the base gasket having it this far down figured i may as well, plenty of room to do it, but i will say these aren't the easiest saws to work on, not bad, but not easy either, the rear carb boot is a PITA for sure, not only getting it back in the top cover, but just trying to fit the air filter back on without it trying to bend back under the cover can be a challenge, small details but worth mentioning, otherwise the saw cleaned up real nice and runs very well now without the base gasket, didn't even give it an MM, just removed the screen....... IMAG0170.JPG IMAG0171.JPG IMAG0172.JPG IMAG0173.JPG IMAG0174.JPG IMAG0175.JPG IMAG0176.JPG IMAG0178.JPG
     
    Last edited: Dec 25, 2015
    old 040, Dec 25, 2015
    #10 Top
    Barcroftb, HDRock, HoneyFuzz and 2 others like this.
  11. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    Love these. Have had 3, 1 4500 orange, 2 450 yellow. Still have the 4500 orange one and 1 450 yellow.

    2nd450v 004.JPG 2nd450v 006.JPG
     
    Cut4fun, Dec 25, 2015
    #11 Top
    Barcroftb, HoneyFuzz, Eric VW and 1 other person like this.
  12. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    Was hope'n you'd chime in Kev............wish i would have looked harder for one of these, i just finished giving the chain a fresh edge, cleaned and checked the bar, all's good, saw is all buttoned back up and ready to rip, if it stays nice out tomorrow, i think i take her out back for a rip!!:D
     
    old 040, Dec 25, 2015
    #12 Top
    HoneyFuzz and Eric VW like this.
  13. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    was actually hoping you meant a solo twin!!................:D
     
    old 040, Dec 25, 2015
    #13 Top
    MasterMech and Eric VW like this.
  14. Eric VW

    Eric VW Moderator

    Joined:
    Jan 6, 2015
    Messages:
    24,398
    Likes Received:
    140,388
    Location:
    US
    Nice work, old 040!
    Great pics, too! Can't wait to see a video of it in the cut:D
     
    Eric VW, Dec 25, 2015
    #14 Top
    old 040 likes this.
  15. HoneyFuzz

    HoneyFuzz

    Joined:
    Jan 20, 2014
    Messages:
    4,484
    Likes Received:
    14,831
    Location:
    Northeast , Ohio
    Looking good buddy !!!
     
    HoneyFuzz, Dec 25, 2015
    #15 Top
    old 040 and Eric VW like this.
  16. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    looks like i'll be owning another 4600 hopefully today thanks to my buddy Andy, at the very least it will be a good parts saw, but i think i'll be able to make it a runner, still got my eyes peeled for a 4500 though..........:whistle: image.jpeg
     
    old 040, Dec 26, 2015
    #16 Top
    HDRock, Eric VW, Cut4fun and 1 other person like this.
  17. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    sorry, my POS camera will do vids but with no sound, so i may just have to get some good pics together out in the woods...........:)...........:tree:
     
    old 040, Dec 26, 2015
    #17 Top
    Eric VW and HoneyFuzz like this.
  18. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    You collect I dont. So they are both open for trades or ;)

    My parts donor 450 that was a runner took apart and dude tried to put helicoils in cylinder where muffler studs go in :zip::rofl: :lol:. He messed that all up. They need fill welded retapped to use cylinder.
    4500 runs and cuts.

    20" bar 12.5" ash

    Dry harden ash that fills like baseball bat hard.

     
    Cut4fun, Dec 26, 2015
    #18 Top
    HDRock, old 040 and Eric VW like this.
  19. Cut4fun

    Cut4fun

    Joined:
    Mar 18, 2014
    Messages:
    1,941
    Likes Received:
    3,571
    Location:
    OHIO Redneck
    450 is apart again for coil. 4500 cutting.

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG] [​IMG] [​IMG]
     
    Cut4fun, Dec 26, 2015
    #19 Top
    HoneyFuzz, old 040 and Eric VW like this.
  20. old 040

    old 040

    Joined:
    Feb 23, 2015
    Messages:
    724
    Likes Received:
    2,288
    Location:
    Buckeye State
    shoot me over a PM on your price or what you may be willing to trade for.............
     
    old 040, Dec 26, 2015
    #20 Top
    HoneyFuzz likes this.
Page 1 of 3