In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Help me out here.

Discussion in 'Chainsaws and Power Equipment' started by Gasifier, Oct 17, 2015.

Page 2 of 2
  1. Mag Craft

    Mag Craft

    Joined:
    Dec 15, 2014
    Messages:
    4,802
    Likes Received:
    27,728
    Location:
    South East Wyoming
    Like everyone has said already. Put some gas in the fuel tank put the cap on and shake it good to rinse the tank out.
    Then put more fuel in it and pump the primer bulb. Dump it out and add more fuel and then run it. Alittle bit of oil left in there will not hurt any thing and it will burn when running the saw. A little bit of smoke for awhile. Your not the first and will not be the last.
     
    Mag Craft, Oct 17, 2015
    #21 Top
    foragefarmer, basod, Moparmyway and 4 others like this.
  2. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,427
    Likes Received:
    103,300
    Location:
    St. Lawrence River Valley, NY
    She is up and running. I made sure it was all drained out and forced out by priming the bulb with the tank cap off. When refilled she started right up with a quick pull of the choke. Smoked like Cheech and Chong at a bong fest :faint:and then cleared right out. I just took down a good size Ash with the 680 before lunch for logs. And the 361P will go to work on the top of it for firewood.:saw:
     
    Gasifier, Oct 17, 2015
    #22 Top
    HDRock, basod, milleo and 8 others like this.
  3. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,141
    Likes Received:
    141,362
    Location:
    Wyoming high plains
    Sounds like you did not sufficiently fill yourself up with caffeine this morning, are you sure you drank the right stuff?
     
    wildwest, Oct 17, 2015
    #23 Top
    Canadian border VT, basod, Stinny and 3 others like this.
  4. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,427
    Likes Received:
    103,300
    Location:
    St. Lawrence River Valley, NY
    I did the filling of tanks with wrong stuff the other day. Just figured out today why it didn't start after I took a break the other day. It may have been I had too much caffeine the other day and was in too much of a hurry.
     
    Gasifier, Oct 17, 2015
    #24 Top
    Canadian border VT, papadave, Mag Craft and 1 other person like this.
  5. papadave

    papadave

    Joined:
    Oct 3, 2013
    Messages:
    18,181
    Likes Received:
    82,470
    Location:
    Right where I want to be.
    CRS:
    Can't Remember Stuff
    Can't Really Say
    Crazy Race Saw
    Cool......crap, now I can't remember.
    I do remember an old adage that goes something like.........."haste makes waste".
    You watch, I'll be the one who does it next.:headbang:
    Nice that worked out Gas. Back to work.
     
    papadave, Oct 17, 2015
    #25 Top
    basod, Stinny, Gasifier and 1 other person like this.
  6. TurboDiesel

    TurboDiesel

    Joined:
    Nov 22, 2013
    Messages:
    16,196
    Likes Received:
    97,190
    Location:
    Hollidaysburg Pa
    x2
     
    TurboDiesel, Oct 17, 2015
    #26 Top
    Canadian border VT, papadave, Gasifier and 1 other person like this.
  7. STIHL250

    STIHL250

    Joined:
    Oct 17, 2015
    Messages:
    91
    Likes Received:
    110
    Location:
    Pennsylvania
    Lol sorry bud that sounds like my luck my father did the same thing a few years back with a poulan gas in oil res n bar oil in gas res just primed it to tank sloshed with gas till it was clean smoked a bit on start up but runs fine good luck
     
    STIHL250, Oct 18, 2015
    #27 Top
    Gasifier likes this.
  8. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,427
    Likes Received:
    103,300
    Location:
    St. Lawrence River Valley, NY
    It's running great now. I cut the top of that Ash all up with it and some other Pine. Nice, lightweight saw.
     
    Gasifier, Oct 18, 2015
    #28 Top
    Chvymn99, pappy88 and Stinny like this.
  9. HDRock

    HDRock

    Joined:
    Oct 4, 2013
    Messages:
    17,249
    Likes Received:
    60,361
    Location:
    Grand Blanc, MI,
    Missed this
    Did the same thing with my little echo , dang thing wouldn't run on pure oil :headbang: rinsed it out there on the spot , fired it up , it did a little smokin
     
    HDRock, Oct 18, 2015
    #29 Top
    Canadian border VT and Gasifier like this.
  10. STIHL250

    STIHL250

    Joined:
    Oct 17, 2015
    Messages:
    91
    Likes Received:
    110
    Location:
    Pennsylvania
    Echo is a good american made saw for sure good luck with ur awesome chainsww
     
    STIHL250, Oct 18, 2015
    #30 Top
    Gasifier likes this.
  11. CoreyB

    CoreyB

    Joined:
    Oct 27, 2015
    Messages:
    1,043
    Likes Received:
    3,420
    Location:
    South east iowa
    I would love to see some photos and videos of the 361p in action. I am very intrigued by this little saw.
     
    CoreyB, Nov 2, 2015
    #31 Top
    Gasifier likes this.
  12. Gasifier

    Gasifier

    Joined:
    Oct 3, 2013
    Messages:
    20,427
    Likes Received:
    103,300
    Location:
    St. Lawrence River Valley, NY
    I'll see if I can catch a video of me tearing through some Ash some day. But then I have to go through the whole youtube thingy, and then .... Yada, yada, yada. :picard: :rofl: :lol:
     
    Gasifier, Nov 2, 2015
    #32 Top
    Chvymn99, concretegrazer and CoreyB like this.
Page 2 of 2