In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Resurrecting More Junk

Discussion in 'Chainsaws and Power Equipment' started by Eric Wanderweg, Nov 15, 2026 at 3:12 PM.

  1. Screwloose

    Screwloose

    Joined:
    Jan 15, 2017
    Messages:
    5,718
    Likes Received:
    33,987
    Location:
    SE Wisconsin
    I have a Subaru on a hydraulic winch, sweet little motor. Small chippers have their place and as long as you don't expect the impossible they work fine.
     
  2. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,809
    Likes Received:
    66,634
    Location:
    Central PA
    I actually have an old Troy-Bilt Tomahawk chipper/shredder and it comes in handy around the house for little stuff but I find myself using it to make wood chips for the smoker more than anything else...lol. I'll rive down a billet of whatever wood I want to chip into 1"×1" or 1"×2" staves and send them through it into a box. Then I take those chips and run them through the flail shredder. Store them in a cardboard box til needed.

    Does that unit of yours have a shredder also?
     
  3. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,809
    Likes Received:
    66,634
    Location:
    Central PA
    I've seen European countries use machines like that and it works well for turning useless woodrows and brushy stands of birch and stuff into usable firewood. Chunk it up, let it season a bit snd shovel it into your appliance. Who knows, if (when) the actual SHTF someday that may be a really good machine to have to use up worthless branches and such.
     
  4. Screwloose

    Screwloose

    Joined:
    Jan 15, 2017
    Messages:
    5,718
    Likes Received:
    33,987
    Location:
    SE Wisconsin
    Old mesh corn cribs would be nice for the chunks.
     
  5. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,809
    Likes Received:
    66,634
    Location:
    Central PA
    They certainly would!
     
  6. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,749
    Likes Received:
    69,568
    Location:
    Bristol, Connecticut
    I’ll call this a success. Chipped/shredded a few 1 & 1/2” and under branches, and several pieces of bark. Works great for its intended use. I was even forcing the branches hard into the side chute and it was chewing away without bogging down.

    IMG_6813.jpeg
     
    JD Guy, eatonpcat, Woodtroll and 9 others like this.
  7. buZZsaw BRAD

    buZZsaw BRAD

    Joined:
    Feb 14, 2019
    Messages:
    35,245
    Likes Received:
    218,341
    Location:
    North Haven, Connecticut
    How large of a limb could it take?
     
  8. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,749
    Likes Received:
    69,568
    Location:
    Bristol, Connecticut
    I’m guessing about 2” max, without really pushing things. I suppose if I was chipping/shredding pine or poplar I could go slightly bigger. At 1.5” diameter it was eating sugar maple branches really nice. That’s probably the sweet spot for this machine. I tossed quite a bit of bark through it and WOW, I’m going to love this machine for that alone. It turns bark into fine powder that’ll be great for a natural mulch.
     
  9. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,749
    Likes Received:
    69,568
    Location:
    Bristol, Connecticut
    Yes, the hopper on the top of the machine seems to shred whatever I feed through it, and the smaller chute in the side is where the chipper knives are. I didn’t even really look at it that closely yet though. I see a bunch of tines looking down from the top.
     
  10. Scotty Overkill

    Scotty Overkill Administrator

    Joined:
    Oct 1, 2013
    Messages:
    9,809
    Likes Received:
    66,634
    Location:
    Central PA
    G
    Get me some exact measurements of the knives on that machine when you get a chance, I'm not sure if they are much the same size as my Troy Bilt. My buddy made me up like 10 or so sets out of tool steel a while back, I'll send you a few pairs if they will work.