In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

Resurrecting More Junk

Discussion in 'Chainsaws and Power Equipment' started by Eric Wanderweg, Nov 15, 2026 at 3:12 PM.

  1. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    I’ve needed a small chipper for years and this came up locally on Craigslist for what I consider to be a reasonable price. Why buy new Chinese when I can skin my knuckles tinkering around with gems like these? Ugly, old, basket case, just my style :) So far all I’ve done to it is remove the engine, elongate the slots on the frame, and mount a Predator motor on it. All that’s left is to make an adapter sleeve for the centrifugal clutch and then bolt the belt guard back on it. I can handle that. The clutch is for a 25mm output shaft and the shaft on the Predator is 3/4”.
    IMG_6798.jpeg IMG_6799.jpeg IMG_6800.jpeg IMG_6802.jpeg

    I have no idea what the original motor was supposed to be. It had this Subaru engine on it when I picked it up, but I saw that water had gotten into the bottom end so I decided to use the low hour Predator engine that I already had, collecting dust. That thing fires right up. I’ll take the Subaru motor to the scrapyard the next time I go.

    IMG_6801.jpeg
     
  2. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    I think that's what my fil had, he had bought it new and never used it much...it had a 8hp Tecumseh on it iirc...I got it going so it could bring the best price at auction...it brought squat, he was a little ticked about it. He said he'd have rather given it to me than enriched the auctioneer more (none of his stuff did well...which I had warned him may be the case, based on my own prior experience at that particular auction)
     
  3. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    As I understand it, these aren’t bad machines either. Made in Ohio to boot. I never had a chipper before so it’s going to be a learning experience.
     
  4. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    From what I hear sharp knives and proper adjustment(s) go a long way toward working good, vs "meh"...makes sense to me
     
  5. ironpony

    ironpony

    Joined:
    Oct 4, 2013
    Messages:
    3,786
    Likes Received:
    21,287
    Location:
    Mid Ohio
    Everyone I know including myself that has used one of these small ones has decided it is not worth it.
     
  6. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    Thank you very, very very much!
     
  7. theburtman

    theburtman

    Joined:
    Feb 26, 2019
    Messages:
    4,228
    Likes Received:
    32,418
    Location:
    Vermont
    My father had a small chipper. I borrowed it one day, and after about half an hour I decided there were more efficient ways to get rid of brush.
     
    metalcuttr, MikeInMa, Eric VW and 2 others like this.
  8. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    I have no illusions that I’m going to be stuffing 6” limbs through this thing and the chips are going to be landing in the neighbor’s yard 17 houses down the street. Before I bought it, I watched a few YouTube videos of these things running. It’s fine for what I need it to do. 1” and under; small stuff. If they were that worthless they never would have sold them to begin with.
     
  9. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    This is exactly what I had in mind for this machine. Bark and twigs. I’m always in need of natural mulch and this is the right tool for the job. Plus for what I spent on this, it was less than a one day rental of a real chipper from big box Orange.
    https://youtube.com/shorts/14QKg7yTAsc?is=4KS2B05vhan5iopR
     
  10. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,337
    Likes Received:
    164,963
    Location:
    NE Ohio
    That's why I said this ^^^, seems that's where many people go wrong...these little ones are just kinda maintenance intensive, and most people "aren't"
    I'm sure some are better than others though...I'm inclined to think these older RH units might be better ones?
    When I got my FILs running I ran like 2-3 sticks through it and "sent it"
    I'm used to running large commercial chippers, so I wasn't overly impressed, but sometimes it's all about expectations management :rofl: :lol:
     
    Last edited: Nov 15, 2026 at 7:29 PM
  11. Eric Wanderweg

    Eric Wanderweg

    Joined:
    Apr 10, 2020
    Messages:
    8,722
    Likes Received:
    69,311
    Location:
    Bristol, Connecticut
    It’s a chipper/shredder by name. Probably more of a shredder than a chipper. Good for leaves, sticks, and I even saw a guy running compost/soil through his. I knew what I was getting into. Probably should’ve stated my intended use at the beginning. I remember hearing more than once that these little machines leave much to be desired (and chipped) Appreciate the feedback regardless.
     
  12. Chud

    Chud

    Joined:
    Aug 15, 2020
    Messages:
    7,345
    Likes Received:
    54,830
    Location:
    NC
    Jeff, Tim and myself drove to Ohio because they wanted to buy a wood chunker. I forgot who makes it. It’s basically a wood chipper with a smaller drum ,engine and a wider gap between the knives and anvil. It’s an interesting machine that could be useful if you wanted to turn small diameter limbs into short firewood lengths. They did not bring along the cash to buy it because at the time they believed the police were confiscating cash. I believe the asking price was 13k and they agreed to buy it. They gave him a down payment and loaded the conveyor on my Tacoma. They drove back to Ohio with a bigger truck and the remaining balance. This was 4-5 years ago and they still haven’t used the chunker. Can you imagine spending that kind of money on a machine and never using it? :rofl: :lol:
    I mean it’s probably a good idea in Europe, or North Dakota where trees are hard to come by.
    I think their big plan was to chunk Hickory, Pecan, Cherry limbs into bags to sell.

    I have a bunch of trees on my lot that are always shedding limbs. A small chipper would be useful for cleanup.
     
  13. Eric VW

    Eric VW Moderator

    Joined:
    Jan 6, 2015
    Messages:
    24,572
    Likes Received:
    141,785
    Location:
    US
    Roto—Hoe… like a Rolodex for certain types of the opposite…. uh, well ya know….
    :whistle:
    :rofl: :lol::wacky:
     
  14. buZZsaw BRAD

    buZZsaw BRAD

    Joined:
    Feb 14, 2019
    Messages:
    35,204
    Likes Received:
    217,970
    Location:
    North Haven, Connecticut
    Handy little machine. Hope you can get it running to your expectations.

    Hopefully you're not pulling a a Richard Crafts? :startled: :whistle:
     
    brenndatomu likes this.
  15. buZZsaw BRAD

    buZZsaw BRAD

    Joined:
    Feb 14, 2019
    Messages:
    35,204
    Likes Received:
    217,970
    Location:
    North Haven, Connecticut
    :rofl: :lol: "What did you do today honey"?

    "I picked up a cheap hoe" !!!
     
    brenndatomu likes this.