In loving memory of Kenis D. Keathley 6/4/81 - 3/27/22 Loving father, husband, brother, friend and firewood hoarder Rest in peace, Dexterday

What's up today (bullchiting) thread.

Discussion in 'Everything Else (off topic)' started by Gasifier, Oct 6, 2013.

Page 5434 of 5434
  1. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,679
    Likes Received:
    144,769
    Location:
    Coastal South carolina
    Thanks. I just need a surface for a makeshift desk for garage. So a crooked cut wouldn't matter, the sheet is here already and hoped to use it. If I'm going to spend $$ on a jigsaw I might as well go to home depot and get plywood cut instead, or I heard somewhere they have scrap bins. It would be smoother than the T1-11 here for sure even with a sheet over it. If the flipping Yukon is not dead.
     
    wildwest, Oct 7, 2026 at 6:43 PM
    #108661 Top
    eatonpcat and brenndatomu like this.
  2. lukem

    lukem

    Joined:
    Oct 4, 2013
    Messages:
    12,294
    Likes Received:
    66,735
    Location:
    IN
    Just clamp down a straight edge with a jigsaw. Never needed to cut a curve on sheeting, but I suppose some do.
     
    lukem, Oct 7, 2026 at 6:46 PM
    #108662 Top
    eatonpcat, brenndatomu and wildwest like this.
  3. lukem

    lukem

    Joined:
    Oct 4, 2013
    Messages:
    12,294
    Likes Received:
    66,735
    Location:
    IN
    Heck, cut it with a chainsaw iffn that's all you got. We cut out windows when framing with a chainsaw and it does a good job.
     
    lukem, Oct 7, 2026 at 6:47 PM
    #108663 Top
    eatonpcat, brenndatomu, wildwest and 1 other person like this.
  4. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,679
    Likes Received:
    144,769
    Location:
    Coastal South carolina
    My husband swore off any home improvement and tools before we moved.
     
    Last edited: Oct 7, 2026 at 8:43 PM
    wildwest, Oct 7, 2026 at 7:08 PM
    #108664 Top
    eatonpcat and brenndatomu like this.
  5. Canadian border VT

    Canadian border VT

    Joined:
    Feb 18, 2015
    Messages:
    19,662
    Likes Received:
    130,800
    Location:
    Vermont
    T111 will make a poor desk top; a scrap counter top would work much better or a door etc etc
     
    Last edited: Oct 7, 2026 at 8:18 PM
    Canadian border VT, Oct 7, 2026 at 8:12 PM
    #108665 Top
    eatonpcat, brenndatomu and wildwest like this.
  6. Woodtroll

    Woodtroll

    Joined:
    Jan 10, 2025
    Messages:
    558
    Likes Received:
    4,365
    Location:
    Mtns of SW VA
    Most lumber stores sell pre-cut small pieces of plywood, 2'x2', 2'x4', etc. fairly reasonably. Might be worth a look to see if you can make one of those work without cutting.
     
    Woodtroll, Oct 7, 2026 at 8:36 PM
    #108666 Top
    eatonpcat, brenndatomu and wildwest like this.
  7. wildwest

    wildwest Moderator

    Joined:
    Jul 21, 2014
    Messages:
    30,679
    Likes Received:
    144,769
    Location:
    Coastal South carolina
    Thanks, 24" deep would be ideal.
     
    wildwest, Oct 7, 2026 at 8:44 PM
    #108667 Top
    eatonpcat and brenndatomu like this.
  8. brenndatomu

    brenndatomu

    Joined:
    May 29, 2015
    Messages:
    25,170
    Likes Received:
    163,621
    Location:
    NE Ohio
    Yup, handy panels I think they're called
     
    brenndatomu, Oct 7, 2026 at 8:50 PM
    #108668 Top
    eatonpcat and sms4life like this.
Page 5434 of 5434